(PHP 4 >= 4.0.4, PHP 5, PHP 7, PHP 8)

gzdeflateComprime una cadena


gzdeflate(string $data, int $level = -1, int $encoding = ZLIB_ENCODING_RAW): string|false

Esta función comprime la cadena dada utilizando el formato de datos DEFLATE.

Para más detalles sobre el algoritmo de compresión DEFLATE ver el documento "» DEFLATE Compressed Data Format Specification version 1.3" (RFC 1951).



Los datos a comprimir.


El nivel de compresión. Se puede dar desde 0 para ninguna compresión hasta 9 para máxima compresión. Si no se especifica, se utilizará el nivel de compresión por defecto de la librería zlib.


Una de las constantes ZLIB_ENCODING_*.

Valores devueltos

La cadena comprimida o false si ocurre un error.


Ejemplo #1 Ejemplo de gzdeflate()

= gzdeflate('Compress me', 9);

Ver también

add a note add a note

User Contributed Notes 9 notes

giunta dot gaetano at sea-aeroportimilano dot it
17 years ago
Take care that that "PHP deflate" != "HTTP deflate".

The deflate encoding used in HTTP is actually zlib encoded.

This is what PHP functions return:
gzencode() == gzip
gzcompress() == zlib (aka. HTTP deflate)
gzdeflate()  == *raw* deflate encoding
anonymous at php dot net
14 years ago
gzcompress produces longer data because it embeds information about the encoding onto the string. If you are compressing data that will only ever be handled on one machine, then you don't need to worry about which of these functions you use. However, if you are passing data compressed with these functions to a different machine you should use gzcompress.
13 years ago
running 50000 repetitions on various content, i found that gzdeflate() and gzcompress() both performed equally fast regardless content and compression level, but gzinflate() was always about twice as fast as gzuncompress().
stockton at wowway dot com
10 years ago
After some searching and experimentation I found that the output from this function cannot be 'inflated' with the objective c 'zlibInflate' wrapper for 'zlib' that is available at http://cocoadev.com/wiki/NSDataCategory but the output from gzcompress() can be. Thank you "anonymous at php dot net" and "tomas at slax dot org" for the clues. I hope this saves someone else the searching.
banditsmile at qq dot com
8 years ago
start from php5.4.0 gzdeflate has the fastest speed and best zip rate.
7 years ago
The HTTP deflate is quite complicated.
The RFC7230, Sec 4.2.2 (https://tools.ietf.org/html/rfc7230#section-4.2.2) says:
«The "deflate" coding is a "zlib" data format [RFC1950] containing a "deflate" compressed data stream [RFC1951] that uses a combination of the Lempel-Ziv (LZ77) compression algorithm and Huffman coding.»
and, also:
«Note: Some non-conformant implementations send the "deflate" compressed data without the zlib wrapper.»

Since this function implements the RFC1951, the compliant encoding of a $payload should be:

tomas at slax dot org
15 years ago
gzcompress() is the same like gzdefflate(), it produces identical data and its speed is the same as well. The only difference is that gzcompress produces 6 bytes bigger result (2 extra bytes at the beginning and 4 extra bytes at the end).
denis dot noessler at red-at dot de
20 years ago
if you have compressed data which is greater than 2 MB (system dependent), you will receive a buffer error by calling the function gzinflate().
be sure to to compress your data by a lower compression level, like 1.
i.e.: gzdeflate($sData, 1);
8 years ago
The "One of ZLIB_ENCODING_* constants." seems to be available only from PHP 5.4.

So I guess that is you are PHP 5.3 you don't use the $encoding parameter...
To Top